Potential problems

If you notice consistent 523, 524, or other error responses, check the System Status Map Open external link and contact support if needed. Railgun will fall back to direct HTTP requests if Cloudflare’s endpoints cannot contact your Railgun daemon, but consistent error responses may indicate a system or origin server problem. When contacting support, please provide a screenshot of http://www.yourdomain.com/cdn-cgi/trace if possible, or a traceroute Open external link to your domain so Cloudflare knows which data center your requests are reaching. You can then pause Cloudflare via the website to disable the service and resume normal website traffic.

Railgun does not perform DNS queries when it receives a request for maximum efficiency and to prevent tampering. This means that the daemon is unaware of NAT routing or firewalls. NAT does not allow for addressing a public interface from within the associated LAN, and Railgun requests will timeout and produce 502 errors. This can be corrected by setting up a static IP mapping. You can set that either through the hosts file for your system (usually at the path /etc/hosts) or through the railgun-nat.conf file in the same directory as the railgun.conf file. Contact support if you require assistance with the NAT configuration file.

​​ Common issues

​​ Requests to example.com:2083 go to port 443

To run Railgun on non-standard ports you need to add the correct mapping to the railgun-nat.conf file. Otherwise, the connection goes to standard ports 80 or 443. Example:

default = 127.0.0.1
example.com:2083 = 127.0.0.1:2083

​​ Railgun returns a 502 error in its error logs

This commonly occurs when Railgun cannot reach your origin web server over port 443 (or port 80) within 30 seconds. Verify that the server your Railgun instance is on can connect via telnet <host> 443.

​​ Railgun returns a connection failed error

If you receive a connection failed 127.0.0.1:443/welcome.cloudflare.com: x509: certificate is valid for www.cloudflare.com, not welcome.cloudflare.com error, this means your origin webserver does not have a certificate matching its hostname. If you are on an internal network and are aware of the risks, you can set validate.cert = 0 in railgun.conf to turn off certificate validation (not recommended).

​​ I am receiving bad Content-Length: "-1" errors

Railgun expects that all POST, PUT, PATCH (and other non-idempotent methods) requests have either a Content-Length header or a Transfer-Encoding: chunked header present.

​​ There are errors containing memcached: connection failed (Unix socket) or dial tcp 127.0.0.1:11211: i/o timeout (TCP) in the logs

Railgun cannot connect to the Memcached server. These errors should not cause visible errors, but will cause Railgun to stream (and not compress) responses.

You should confirm that Memcached is running, is accepting connections, and confirm the state of your Memcached server via the Memcached stats command.

​​ How can I tell what the compression ratio for a request is?

rg-diag is installed alongside Railgun, and allows you to decode the Cf-Railgun header. Example:

$ bin/rg-diag -decode="151df128a1 2.05 0.009465 0031 5360"

Compression ratio 2.05%
Railgun version 5360
Railgun Flag map.file used to change IP
Railgun Flag rg-sender sent dictionary
Railgun Flag rg-listener found dictionary

​​ Support

When contacting Cloudflare Support Open external link , provide the following information (if available):

• Your railgun.conf and railgun-nat.conf (if applicable) files.
• Output from /var/log/messages from Railgun.
• A copy of /var/log/railgun/panic.log, if not empty.

Providing the IP address or hostname of your Railgun server will also allow our Support team to test connectivity remotely. Please let us know if you have a firewall protecting your Railgun server when creating a support request.